Search Northern Tool

Looking for Answers about SunStar Heating Products Infrared Ceramic Heater - LP, 100,000 BTU, Model# SG10-L?

Air Tools + Compressors(Q:1392 A:1929)
Automotive(Q:2431 A:3247)
Clothing + Work Wear(Q:137 A:158)
Construction(Q:691 A:899)
Electrical(Q:255 A:326)
Engines(Q:373 A:460)
Fans(Q:691 A:834)
Farm + Acreage(Q:754 A:893)
Food Processing(Q:299 A:419)
Generators(Q:1638 A:2301)
Hand Tools(Q:362 A:437)
Hydraulics(Q:1020 A:1128)
Lawn + Garden(Q:2529 A:3452)
Lighting(Q:194 A:238)
Logging(Q:406 A:615)
Material Handling(Q:974 A:1174)
Metal Fabrication(Q:656 A:772)
Power Tools(Q:812 A:1305)
Pressure Washers(Q:1073 A:1449)
Safety(Q:144 A:203)
Seats(Q:341 A:472)
Security Equipment(Q:270 A:400)
Snow + Ice Removal(Q:278 A:349)
Sporting Goods + Toys(Q:536 A:715)
Storage + Organizers(Q:692 A:946)
Tires + Wheels(Q:634 A:816)
Trailers + Towing(Q:1649 A:2043)
Water Pumps(Q:1158 A:1410)
Welding(Q:693 A:1115)
Winches(Q:396 A:505)

Customer Questions & Answers for
SunStar Heating Products Infrared Ceramic Heater - LP, 100,000 BTU, Model# SG10-L

Item# 16307
The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility not recommended for car washes. This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage, Item #16284 or 24V thermostat, Item #16342, both sold separately. May require the following second stage regulators prior to the heater based on gas supply pressure A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure both sold separately. NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE Please review the detailed Installation & Operating Instructions attached for other specific installation requirements gas pressure, ventilation etc. prior to purchasing the heater. Thermostat Included No, Blower Included No, Gas Inlet in. 1/2, BTU Output 100,000, Clearance from Corner in. 49, Clearance from Rear Wall in. 49, Clearance from Side Wall in. 49, Dimensions L x W x H in. 33 x 31 x 11, Heating Capability sq. ft. 2,500, Igniter Direct spark, Needs Direct Venting No, Product Type Radiant heat, Regulator Included No. Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 16ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material 65in. above, 129in. below and 49in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column WC and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator sold separately to reduce it to less than 14in. WC or 1/2 PSIG No assembly required Heaters are 100 test-fired prior to shipment CSA design certified
Customer Questions & Answers:
1 Question
 | 
1 Answer
Product Details

Questions & Answers for SunStar Heating Products Infrared Ceramic Heater - LP, 100,000 BTU, Model# SG10-L

Question

What size heater should I get?

My garage workshop is a 12 X 25x12 ft side walls and a peaked roof. It is an all metal building with no insulation. I live in upstate NY and 0 degrees is common. What size heater and type should I purchase? It will need to run off propane and I would like electronic ignition so there is no pilot to have to light.
asked 9 months ago
by
Seamates
 - Western New York Sate
on SunStar Heating Products Infrared Ceramic Heater - LP, 100,000 BTU, Model# SG10-L
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
Staff Answer
The SunStar Infrared Ceramic Heater would not be recommended for installation for any height less than 16 feet above finished floor surface. A good option for your apparent situation would be Northern Item # 29127. Always check with local codes and ordinances to make sure you are in compliance for installation.
answered 9 months ago
by
ProductExpert25
0points
0out of 0found this answer helpful.
1 of 1