This powerful 37 ton NorthStar® Log Splitter will split any log that gets in its way in either in a vertical or horizontal position. Powered by a Honda GX270 engine with an exclusive idle down feature that saves fuel and reduces noise while you load the next log. The Barnes hydraulic pump intelligently adjusts flow and pressure by delivering high flow/low pressure when there is no resistance and low flow/high pressure when cutting through a log to reduce travel time and increase productivity. Add the 4-Way Wedge Wings (Item #1143) to quarter logs with one split instead of three. Ram Force (Tons): 37, Max. Log Size L x W (in.): 25 x 16, Continuous Force (Tons): 34.3, Engine: Honda GX with idle control, Engine Displacement (cc): 270, Gross Torque: 14.1 at 2,500 RPM, Low Oil Shutdown: Yes, Cycle Time (sec.): 14, Automatic Cylinder Return: Yes, Cylinder: 5 in. x 24in., Pump: Barnes 16 GPM, 2-stage, Max. PSI: 3,500, Oil Reservoir (gal.): 9, Fuel Capacity (gal.): 1.4, Hoses: Yes, Log Cradle: Yes, Log Lift: No, Jack Stand: Yes, Ball Coupler (in.): 2, Tire Size: 4.80 x 8, Lights: No, Fenders: No, Pre-assembled: No, Dimensions L x W x H (in.): 90 x 43 x 42 Auto idle/throttle control for extended engine life, improved fuel economy and reduced engine noise 2-stage pump allows the log splitter to achieve the same pressures as a single stage pump, while using less horsepower Patented log stripper clears log from retracting wedge Industrial-grade full beam construction A log cradle centers the log on the wedge and prevents it from rolling off of the beam Coupler for 2in. ball High speed tires for towing 9 gallons hydraulic oil required (not included) Included engine guard protects engine from split logs Replacement parts are available through Northern Tool Parts Department 1-800-270-0810

Customer Questions & Answers:

24 Questions

63 Answers

Ask a New Question

Overall Rating:

4.7

out of

Read All 145 Reviews145

Questions & Answers for NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

Question

30 ton vs. 37 ton

I am a homeowner who will split 8-10 cords per year. What would the 37 ton offer me vs. the 30 ton? Bigger engine, piston, pump means what? Thanks

asked 1 year, 8 months ago

Anonymous

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

+2points

2out of 2found this question helpful.

7 answers

Answers

answer 1

With the 37 ton splitter you will get a bigger engine, bigger pump, and bigger cylinder. What this means for you, is faster cycle time and ability to split bigger harder logs. Also, the engine on the 37 ton splitter has an idle control feature so that when the engine is not under load it will "idle down" to save fuel and reduce noise. A great addition to either of these splitters is a set of 4 way wedge wings (item#1143) to split logs into 4 pieces in one shot. See link below for more details.

Products from my answer

NorthStar Wedge Wings for Log Splitter

(24)

answered 1 year, 8 months ago

NorthstarExpert13

+3points

3out of 3found this answer helpful.

answer 2

I have used both, but recommend the 37ton for the power that it has. It is a little more, but depending on what type of wood you split or whether or not it is green or dry will make all the difference in the world when using one or the other. If green, the 37ton will push through the wood, even tearing, which makes a mess and a problem stacking. If dry, either will be fine. If you consider the attachable blades, make sure that the size of the split wood is to your liking, because that on the lower side, will be smaller. Good Luck!

answered 1 year, 8 months ago

POPPY1050

- Freindswood, Texas

+1point

1out of 1found this answer helpful.

answer 3

MY neighbor has the 30 ton unit, it is a bit slower, but does the job, My 37 ton unit does between 10-12 cords each year, it is a bit faster but also has the extra power to break the tough ones. I would recommend the 37 ton.

answered 1 year, 7 months ago

BigB619

- Prospect, CT

+2points

2out of 2found this answer helpful.

answer 4

I watched the sales and when all was said and done the NT 37 ton was just not that more expensive. Check out the type of engine used on splitter candidates. Don't just look at the name on the engine, actually look at the specs on the engine company website and in the NT engine comparison manual which is usually kept in the NT stores with the replacement engines. The Honda engine on the 37 is industrial design with better bearings and cylinder liners for better longevity, dependability, and resale value. The auto-idle feature is good for taking an occasional break and probably results in better gas consumption. I split a little less wood than you are talking about and I wouldn't use any less than 37 ton. Good cycle time, great power. The ram/wedge has great design which means the wood splits well with fewer kick-outs..check out my review with further comments on wedge design which prevents lateral strain on the hydraulic cylinder.

answered 1 year, 6 months ago

JRogers

- Blue Ridge, VA

+5points

5out of 5found this answer helpful.

answer 5

What you need to look at is cycle time the 14 second is the way to go some larger and also smaller dont have that cycle time. the 37 is a good one.

answered 1 year, 1 month ago

D6CAT

- north carolina

+1point

1out of 1found this answer helpful.

answer 6

You'll be able to split the wood faster with less stress on the engine.

answered 1 year, 6 months ago

WebGirl

- Sussex, WI

+3points

3out of 3found this answer helpful.

answer 7

The 37 ton has an 8 hp motor, the 30 ton has a 4.6 hp motor, so you gain about 40% more power I always opt for the heavier duty tools it just puts less stress on the unit, especially a log splitter so I bought the 37 ton. I would think that the 30 ton would handle all but the knottiest tree stumps. I had an old 25 ton splitter that a piece of knotty walnut cracked the splitting head. It was an different design with the wedge attached to the frame, the splitting head on these is attached to the ram..

answered 1 week, 1 day ago

2PPacker

- Lenexa, Ks

0points

0out of 0found this answer helpful.

Question

How big is the crate or container for item 1114 if I pick it up from one of your stores? I need to know if it will fit in my pickup truck bed. Thanks,

asked 1 year, 2 months ago

Narget

- Madison TN

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

0points

0out of 0found this question helpful.

6 answers

Answers

answer 1

This NorthStar log splitter is packaged twice and wrapped on a metal crate measuring 75.25 inches long, 26 inches wide, and 19 inches high.

It also has a smaller box on top measuring 30.5 inches long, 23.75 inches wide, and 21.5 inches high.

answered 1 year, 2 months ago

NorthstarExpert11

+4points

4out of 4found this answer helpful.

answer 2

Its on its own steel cradle and its heavy, about 650 lbs. I think it would fit in a full sized P/U bed, but you'll need a fork lift to get ot out. As some of the other reviewers said, you'll also need a way to lift the ram assembly to bolt it to the base. Don't forget the oil, it takes 7+ gals. With all this its worth it. It will split massive forked logs.

answered 1 year, 2 months ago

RonfT

- Las Vegas, NV

+1point

1out of 1found this answer helpful.

answer 3

yes it will a full size pick up

answered 1 year, 2 months ago

bigred340

+1point

1out of 1found this answer helpful.

answer 4

You can get it in the back of a truck but,you will have to have some help [3-4 people] getting it out.The engine comes in its own box and everything else is on a steel pallet.

answered 1 year, 2 months ago

MnTim

- Harris, Mn

+1point

1out of 1found this answer helpful.

answer 5

yes you can pickup if you have full size pickup. You will need someway or help to unload when you get home

answered 1 year, 1 month ago

D6CAT

- north carolina

+1point

1out of 1found this answer helpful.

answer 6

I have a 03 f350. with a 8 foot bed and a tool box. the unit itself took up alot of space. so the engine was traped between the side of the box and the splitter. the engine comes in a seprate box.I hade no truble with halling it in a snow storm for 150 miles bact to ware i live.

answered 1 year, 1 month ago

triggerel690

- deerwood MN

+1point

1out of 1found this answer helpful.

Question

What is the best way to winterize the engine?

I want to store this through the winter and use again in spring.

Products related to my question

Youngstown Warrior Reinforced Palm Utility Glove - Large

(4)

Youngstown Warrior Reinforced Palm Utility Glove - Medium

(1)

Youngstown Mesh Utility Plus Gloves - Medium

asked 1 year, 6 months ago

WebGirl

- Sussex, WI

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

0points

0out of 0found this question helpful.

4 answers

Answers

answer 1

Please see page 24 of the product manual for storage procedures. The manual is located beneath the product Q & A tab.

answered 1 year, 6 months ago

NorthstarExpert11

+2points

2out of 2found this answer helpful.

answer 2

put stabil in gas tank and cut the gas off and let engine run until the gas is out of the carbrater and it will be good for the winter

answered 1 year, 6 months ago

Donald4130

- Newport, Tennessee

+2points

2out of 2found this answer helpful.

answer 3

Use Sea Foam fuel stabilizer at recommended rate in the fuel remaining in tank. Start engine and allow it to warm up. The Honda engine has a fuel shut off valve. Close valve and run engine until it dies, emptying carburetor. Drain engine oil and replace - I use synthetic oil after initial break-in. It will not oxidize or break down over the winter. Some folks say to wait until spring and change oil before start up. Either works. If you choose not to use fuel stabilizer, siphon or suck out as much remaining fuel as you can. Store out of weather.

answered 1 year, 6 months ago

JRogers

- Blue Ridge, VA

+1point

1out of 1found this answer helpful.

answer 4

Drain the fuel if you want to store and get gas out of carb. I work on small engines and think its bettter just to start once a month and let run ten minutes

answered 1 year, 1 month ago

D6CAT

- north carolina

0points

0out of 0found this answer helpful.

Question

What length log will it take

37 ton log splitter

asked 1 year, 4 months ago

bill24

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

-1point

0out of 1found this question helpful.

4 answers

Answers

answer 1

This unit will split logs up to 25" in length.

answered 1 year, 4 months ago

NorthstarExpert13

0points

0out of 0found this answer helpful.

answer 2

25 inches

answered 1 year, 2 months ago

wrench1976

- shumway, il

0points

0out of 0found this answer helpful.

answer 3

25"

answered 6 months ago

samndbo

- Pennsylvania

0points

0out of 0found this answer helpful.

answer 4

25" or shorter will fit.

answered 1 week, 1 day ago

2PPacker

- Lenexa, Ks

0points

0out of 0found this answer helpful.

Question

if i buy this product will it be assembled?

asked 1 year, 3 months ago

Anonymous

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

0points

0out of 0found this question helpful.

4 answers

Answers

answer 1

No,This NorthStar log splitter is packaged twice but on the same crate and wrapped.

The first box is placed on top of the metal crate containing the engine and pump assembly.

The second is the metal crate containing the main sub-frame and cylinder.

answered 1 year, 3 months ago

NorthstarExpert11

0points

0out of 0found this answer helpful.

answer 2

The only 'assembly' consists of sliding the handles into the holders. No tools necessary. In fact, you don't even need to bend over to get them in there.

answered 1 year, 3 months ago

Flaitheas

- Michigan

-3points

0out of 3found this answer helpful.

answer 3

this prduct does not come ssembald. you will need to do that with a basic tool set. and a extra person to help lift things. I have did it all by my self and that sucked it is varry haevy. you will also need to buy any fluid that it needs to run. ( engin oil, hydrolic fluid,and greese for a greese gun ) and then wedge needs to be greesed befor every use. thare are greese serts ware the wedge is for the greese.

answered 1 year, 1 month ago

triggerel690

- deerwood MN

+1point

1out of 1found this answer helpful.

answer 4

No, but it is so simple and hoses are color coded, very few basic tools needed

answered 6 months ago

samndbo

- pa

-1point

0out of 1found this answer helpful.

Question

What is the log capacity?

asked 1 year, 2 months ago

Anonymous

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

0points

0out of 0found this question helpful.

4 answers

Answers

answer 1

This splitter is compatible with logs that are up to 25" long.

answered 1 year, 2 months ago

NorthstarExpert13

+1point

1out of 1found this answer helpful.

answer 2

25" but there is a point on the top of the wedge so if the log is not even you can get the log side in and split that way.

answered 1 year, 2 months ago

Ghostrider272

- Central, MN

+1point

1out of 1found this answer helpful.

answer 3

I can split 24 easy must be 26. Great tool

answered 1 year, 1 month ago

D6CAT

- north carolina

+1point

1out of 1found this answer helpful.

answer 4

It will take a log up to 25" long.

answered 1 week, 1 day ago

2PPacker

- Lenexa, Ks

0points

0out of 0found this answer helpful.

Question

NorthStar vs. TroyBuilt

37 Ton North Star vs. 33 ton Troy Built. Besides price and
force what makes NorthStar better than TroyBuilt?

asked 1 year, 5 months ago

twosmoke123

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

0points

0out of 0found this question helpful.

3 answers

Answers

answer 1

Because we do not sell the Troy Bilt log splitters at Northern, I am not able to compare them for you feature by feature. The NorthStar brand has made its place in the industry by offering equipment that has unparalleled quality and longevity. This NorthStar splitter features top quality components from top to bottom, starting with a commercial grade Honda GX engine and a Barnes/Haldex hydraulic pump. The Northstar splitters are engineered, developed and tested in the United States by NorthStar (a division of Northern Tool and Equipment). These units have been torture tested, refined and engineered by us, so we have had the ability to develop these splitters into a quality class that is all by itself. As a testament to the quality of these units, our customers who have purchased this splitter, have given it overwhelmingly positive ratings. Check it out for yourself, the customer reviews can be found below the add to cart link on the product page.

answered 1 year, 5 months ago

NorthstarExpert13

0points

0out of 0found this answer helpful.

answer 2

I have both North Star and Troy Built tools. I have had a better track record with North Star than Troy Built. I once bought a Troy Built Shredder that was Trouble with a capital "T". That has put me off a bit to Troy Built, however I am contemplating buying a Troy Built tiller in the near future. North Star is essentially OEMed part components bolted together to make a tool. The Honda engine is the most quiet and easy to start that I have encountered to date.

answered 1 year, 2 months ago

clew

- Mitchellville, Maryland

0points

0out of 0found this answer helpful.

answer 3

Don't buy troybuilt anything they are not what they used to be. The 37 ton is great. Service it and keep it dry it will make you a good tool

answered 1 year, 1 month ago

D6CAT

- north carolina

0points

0out of 0found this answer helpful.

Question

Is Engine Oil included?

asked 2 months ago

Anonymous

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

0points

0out of 0found this question helpful.

3 answers

Answers

answer 1

The engine oil is not included with the NorthStar log splitter. The manual does provide information as to the oil that should be used.

answered 2 months ago

NorthstarExpert12

0points

0out of 0found this answer helpful.

answer 2

No engine oil is note included

answered 2 weeks, 1 day ago

1HandyDad

- Woodstock, Maryland

0points

0out of 0found this answer helpful.

answer 3

No, engine oil or hydraulic oil are not included.

answered 1 week, 1 day ago

2PPacker

- Lenexa, Ks

0points

0out of 0found this answer helpful.

Question

The Cyl is 5 x 24 what is the dia. of the rod?

Products related to my question

NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

(145)

asked 1 year ago

Anonymous

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

0points

0out of 0found this question helpful.

3 answers

Answers

answer 1

The rod diameter of the cylinder is 2".

answered 1 year ago

NorthstarExpert12

0points

0out of 0found this answer helpful.

answer 2

answered 6 months ago

samndbo

- Pennsylvania

0points

0out of 0found this answer helpful.

answer 3

The rod is about 1 15/16 inches thick

answered 1 week, 1 day ago

2PPacker

- Lenexa, Ks

0points

0out of 0found this answer helpful.

Question

What is this compareable to in Horsepower

what does 270cc compare to in engine HP?

asked 1 year, 3 months ago

Anonymous

on NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

0points

0out of 0found this question helpful.

3 answers

Answers

answer 1

This NorthStar log splitter is equipped with a Honda 270cc engine, which is approximately 9 horse power.

answered 1 year, 3 months ago

NorthstarExpert11

0points

0out of 0found this answer helpful.

answer 2

270cc is about 9 HP.

answered 1 year, 2 months ago

MnTim

- Harris, Mn

0points

0out of 0found this answer helpful.

answer 3

Pretty sure its 9hp.

answered 1 year, 2 months ago

MattfromMaine

- Moosehead Lake, Maine

0points

0out of 0found this answer helpful.

1 2 3 next>>

Looking for Answers about NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc?

Customer Questions & Answers for NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

Questions & Answers for NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc

30 ton vs. 37 ton

How big is the crate or container for item 1114 if I pick it up from one of your stores? I need to know if it will fit in my pickup truck bed. Thanks,

What is the best way to winterize the engine?

What length log will it take

if i buy this product will it be assembled?

What is the log capacity?

NorthStar vs. TroyBuilt

Is Engine Oil included?

The Cyl is 5 x 24 what is the dia. of the rod?

What is this compareable to in Horsepower

Customer Questions & Answers for
NorthStar Horizontal/Vertical Log Splitter - 37-Ton, 270cc